BAUMR-AG CS-355s: Quick Verdict
The BAUMR-AG CS-355s is a 355mm corded metal cut-off saw using a low-speed ceramic-alloy toothed blade rather than a conventional high-speed abrasive disc.
Its published specification includes a 2400W motor, 1200 RPM blade speed, 25.4mm blade bore, 0–45 degree mitre adjustment and an integrated workpiece vice.
Its main appeal is the ability to make relatively clean dry cuts in suitable metal profiles with considerably less spark and abrasive debris than a conventional abrasive cut-off wheel.
However, low spark does not mean spark-free, and the CS-355s should not be treated as safe around combustible or flammable materials.
Testing statement: Firebusters has not personally tested or operated this saw. This guide is based on the current BAUMR-AG and Edisons listings, the CS-355s manual and Australian workplace-safety guidance.
Verified CS-355s Specifications
| Model | CS-355s |
| SKU | SAWMCTBM3CSA |
| Motor | 2400W corded electric |
| Supply | 240V 50Hz |
| Plug | Standard Australian 10A |
| Power cord | Approximately 2.1m |
| Blade | 355 × 3 × 25.4mm ceramic-alloy toothed blade |
| Blade speed | 1200 RPM |
| Mitre range | 0–45 degrees |
| Product weight | Approximately 23kg |
| Dimensions | Approximately 74 × 45 × 60cm |
Published Cutting Capacities
The shape of the stock matters. A single headline cutting diameter does not tell you whether a saw will accommodate your particular section.
| Material profile | 90° | 45° |
|---|---|---|
| Rectangular | 210 × 85mm | 135 × 43mm |
| Square | 120 × 120mm | 85 × 85mm |
| Round pipe | 130mm | 90mm |
| Angle steel | 200 × 200mm | 130 × 130mm |
These are manufacturer-published maximum capacities. They should not be interpreted as confirmation that every material, wall thickness or alloy within those dimensions is suitable for the supplied blade.
2400W Alone Does Not Tell You How Well It Cuts
Motor wattage is electrical input power. It should not be used by itself to predict cutting speed, finish or blade life.
For a metal cut-off saw, useful comparison points include:
- Blade type and tooth geometry
- Blade diameter and bore
- Blade speed
- Material and wall thickness
- Workpiece clamping
- Feed pressure
- Blade condition
- Motor characteristics
The important feature of the CS-355s is therefore not simply its 2400W rating. It is the combination of a 355mm toothed blade running at approximately 1200 RPM with a vice and mitre fence designed for cut-off work.
Is It Really a Cold Saw?
BAUMR-AG markets the CS-355s as a “Cold Cut Off Saw”. It uses a toothed ceramic-alloy blade operating at approximately 1200 RPM and is also described by the supplier as a dry-cut saw.
For buyers, the useful distinction is that it does not use the high-speed resin-bonded abrasive wheel normally found on a conventional abrasive chop saw.
That means it should be compared with other low-speed toothed dry-cut metal saws rather than assuming every machine sold under the term “cold saw” has the same design.
Cold/Dry-Cut Saw vs Abrasive Saw vs Bandsaw
| Tool type | Why choose it? | Main trade-off |
|---|---|---|
| CS-355s dry-cut saw | Repeat crosscuts and mitres in suitable metal profiles with a toothed blade | Blade suitability and workpiece clamping are critical; 23kg machine |
| Abrasive cut-off saw | Relatively simple cutting of suitable steel stock using replaceable abrasive discs | Typically produces considerably more sparks, abrasive dust, heat and burr |
| Metal bandsaw | Controlled cutting of varied stock, often with low spark generation | Usually slower and may require more workshop space or setup |
No one process is best for every workshop. Choose according to material, cut frequency, required finish, available space and the types of profiles you actually use.
Important Material Restrictions in the Manual
The sales page lists a wide range of materials, but the CS-355s manual is more restrictive.
The manual specifically identifies the following as not suited for cutting:
- Hollow thin-wall stainless-steel materials
- Chromium-plated metal materials
- Metallic materials with quenched hardness
- Iron or steel wire
- Other special materials outside the tool’s intended application
Professional Advertising vs Domestic-Use Manual
The current product advertising describes the saw as suitable for professionals and DIY users.
However, the CS-355s manual contains a statement that the equipment is designed for domestic use only.
The Vice Is a Safety Feature, Not Just a Convenience
The CS-355s has an integrated vice and adjustable mitre fence. The manual specifically instructs users to secure the workpiece rather than holding it by hand.
The manual also says not to cut a workpiece that is too small to be secured properly.
Before each cut:
- Place the workpiece firmly against the fence.
- Clamp it securely in the vice.
- Support long stock so its weight does not twist or lift the workpiece.
- Check that the blade path clears the vice, fence and supports.
- Do not hold loose or undersized material by hand.
Poor workholding can allow the material to move, rotate or bind the blade.
Blade Guard and Blade Condition
The saw uses a retractable lower blade guard.
The manual says the protective cover should be checked for correct operation and must not be secured in the open position.
Do not use a blade that is:
- Blunt
- Cracked
- Bent
- Damaged
- Incorrectly sized for the saw
The manual also warns against using high-speed-steel blades on this machine.
Disconnect the plug before blade removal, installation, cleaning or adjustments requiring access to the blade area.
Blade Replacement: Check More Than Diameter
The supplied blade specification is:
- Diameter: 355mm
- Kerf/thickness: 3mm
- Bore: 25.4mm
- Saw speed: 1200 RPM
BAUMR-AG’s replacement ceramic-alloy blade is rated to a maximum of 1250 RPM.
Low Spark Does Not Mean No Fire Risk
The toothed dry-cut blade is marketed as producing substantially fewer sparks and less heat than an abrasive wheel.
That is useful, but it should never be translated into “safe around flammables”.
The CS-355s manual says not to operate the machine in flammable or explosive environments because power tools can produce sparks or heat capable of ignition.
WorkSafe Victoria also identifies cutting and grinding as hot-work activities capable of starting fires from sparks, heat and hot material.
- Remove combustible material from the cutting area.
- Check beneath and behind the cutting location.
- Keep flammable liquids and vapours away.
- Do not cut drums or tanks that have contained flammable or combustible liquids.
- Inspect the area after cutting where there is potential for ignition.
Metal Chips and Hot Offcuts
A toothed dry-cut saw generally produces metal chips rather than the same abrasive dust stream as a resin-disc chop saw.
Those chips can still be sharp, hot and capable of being thrown from the cutting area.
The manual specifically says:
- Do not remove chips while the blade is still rotating.
- Keep the cutting area clear of loose metal debris.
- Keep floors clear to reduce slip and trip hazards.
- Use appropriate eye protection.
Allow cut material and the blade to cool before handling where necessary.
Noise Still Requires Attention
A low-speed toothed metal saw may sound different from an abrasive saw, but it should not automatically be described as quiet.
WorkSafe Victoria notes that circular saw noise can vary widely depending on blade design, blade condition, material, speed and feed rate.
For workplace use, noise exposure should be assessed rather than assuming hearing protection alone solves the issue.
Electrical Supply
The CS-355s is specified for:
- 240V
- 50Hz
- 2400W
- Standard Australian 10A plug
- Approximately 2.1m power cord
The manufacturer also provides soft-start functionality.
A soft-start system reduces the abrupt starting behaviour of the motor, but it does not mean every power board, extension lead, generator or shared circuit is automatically suitable.
Follow the current manual for electrical requirements and use appropriately rated equipment. Inspect leads and plugs before use and use RCD protection as required.
Workshop Space and Material Support
The saw itself measures approximately 74 × 45 × 60cm and weighs around 23kg.
The working space required can be much greater once long lengths of steel tube, angle or box section are added.
Before buying, consider:
- Bench or stand strength
- Infeed and outfeed clearance
- Support for long workpieces
- Room to operate the vice
- Safe operator position
- Collection and cleanup of metal chips
A roller stand or other appropriate support may be useful for long stock, but it does not replace the saw’s vice or correct workholding.
Who Might Consider the CS-355s?
Possible good fit
- Home fabrication workshops
- Repeated cutting of suitable box section and tube
- Fence, gate and general metal projects
- Users wanting lower-spark dry cutting than an abrasive chop saw
- Users needing repeatable 0–45° mitre cuts
Consider another machine if
- You mainly cut hardened or restricted materials
- You need very quiet operation
- You frequently need highly portable equipment
- You need long unattended cuts that suit a bandsaw better
- You require a commercial-use machine and cannot resolve the manual’s domestic-use statement
Questions to Ask Before Buying
- What material will you cut most often?
- Does the manual permit that material?
- Will your largest stock fit the published profile capacity?
- Is a 25.4mm bore replacement blade readily available?
- Can the workpiece be securely clamped?
- Do you have enough room to support long stock?
- Is 23kg manageable if the saw needs to be moved?
- Would a metal bandsaw better suit your workflow?
- For commercial use, has intended use and warranty coverage been confirmed?
Frequently Asked Questions
What is the exact model?
The current model is the BAUMR-AG CS-355s, supplier SKU SAWMCTBM3CSA.
What speed does it run at?
The published blade speed is 1200 RPM.
What blade does it use?
The supplied blade is a 355 × 3 × 25.4mm ceramic-alloy toothed blade.
Does it plug into a normal Australian outlet?
The current specification lists a standard Australian 10A plug with 240V 50Hz supply.
How heavy is it?
Approximately 23kg.
Does it produce sparks?
The manufacturer describes the toothed blade as producing much less sparking than conventional abrasive cut-off wheels. It should not be described as spark-free, and the manual prohibits operation in flammable or explosive environments.
Can it cut stainless steel?
The manual specifically lists hollow thin-wall stainless-steel material as unsuitable. Check the exact material and blade requirements before attempting stainless-steel cutting.
Can I use it commercially?
The sales material promotes professional use, but the CS-355s manual says the equipment is designed for domestic use only. Confirm intended-use and warranty conditions with the supplier before commercial use.
Has Firebusters tested this saw?
No. Firebusters has not personally tested or operated the CS-355s. This guide is based on published manufacturer, supplier, manual and Australian safety information.
Final Assessment
The BAUMR-AG CS-355s fills a useful position between a conventional abrasive chop saw and a metal bandsaw.
Its 355mm ceramic-alloy toothed blade, 1200 RPM operating speed, integrated vice and 0–45° mitre adjustment make it potentially useful for repeated dry cuts in suitable metal stock.
The 2400W motor is only one part of that equation. Blade selection, material compatibility, secure clamping and cutting capacity matter just as much.
The most important information missing from a simple sales summary is found in the manual: several material types are specifically excluded, the workpiece must be secured in the vice, the blade guard must remain functional, and the manual states domestic use only.
Our recommendation: consider the CS-355s if you regularly cut compatible metal profiles and prefer a toothed low-speed cut-off saw over an abrasive wheel. Before buying for trade use, specialised alloys or stainless-steel work, confirm the application directly with the supplier.
Research Sources
-
BAUMR-AG – CS-355s product specifications
-
Edisons – CS-355s product listing
-
BAUMR-AG CS-355s instruction manual
-
WorkSafe Victoria – hot-work fire hazards
-
WorkSafe Victoria – circular-saw noise
Research checked September 2026. Specifications, blade availability, warranty and product details may change.
© Firebusters. General information only. Firebusters has not personally tested this product. Always follow the current manufacturer instructions and applicable Australian workplace and electrical safety requirements.
