Workshop Saw Comparison and Safety Guide for Australian DIY

Affiliate disclosure: Firebusters may receive a commission if you purchase through some links on this page, at no additional cost to you.

Workshop Saw Comparison for Australian DIY Projects

This guide compares four BAUMR-AG corded workshop saws: two table saws, one sliding compound mitre saw and one benchtop bandsaw. Each type performs a different job, so the right choice depends on the material, cut, workspace and operator experience.

Testing statement: Firebusters has not personally tested these saws. Specifications come from current manufacturer and merchant listings and should be checked before purchase.

Quick distinction: Table saws suit repeated ripping and straight cuts, mitre saws suit controlled crosscuts and angles, and bandsaws suit curved cuts and suitable irregular shapes.

Models Compared

BTB60: 2000W table saw with a 254mm blade, laser guide and extendable table.
BTB50: 2000W table saw with a 255mm blade, greater published cutting depth and expandable worktop.
SBR-210: 1500W sliding compound mitre saw with a 210mm blade.
BS40: 500W benchtop bandsaw with a 1712mm band blade.

Verified Specification Comparison

Model	Type	Motor	Blade	Published capacity	Weight
BTB60	Table saw	2000W	254mm	Blade height adjustment listed as 3–74mm; bevel and mitre up to 45°	22kg
BTB50	Table saw	2000W	255mm, 60-tooth listed	85mm at 90°; 65mm at 45°; mitre ±45°	20kg
SBR-210	Sliding compound mitre saw	1500W	210mm, 24-tooth listed	305 × 70mm at 0°/90°; 215 × 70mm at 0°/45°	11kg
BS40	Benchtop bandsaw	500W brushless	1712mm band; 3.5–12mm listed width	115mm cutting height; 245mm cutting width	24kg

BAUMR-AG BTB60 254mm Table Saw

The BTB60 is a 2000W corded table saw with a 254mm blade. Its table extensions increase the published worktop width from approximately 72cm to 92cm.

10A Australian plug
Two-metre power cord
Mitre adjustment to ±45 degrees
Blade bevel adjustment to 45 degrees
Adjustable rip fence
Laser alignment guide
Blade guard and splitter listed
Dust-extraction connection
Stand and accessory assembly required

Possible fit: Repeated straight, rip, mitre and bevel cuts where a supported table and adjustable fence are useful.

Limitations: The merchant lists the blade-height adjustment as 3–74mm but does not clearly publish a separate maximum cutting depth at every angle. Confirm the required capacity against your material before ordering.

Check BTB60 details →

BAUMR-AG BTB50 255mm Table Saw

The BTB50 is a separate 2000W table-saw model with a 255mm blade. Its published maximum cutting depth is 85mm at 90 degrees and 65mm with the blade bevelled to 45 degrees.

255mm carbide-tipped, 60-tooth blade listed
Bevel adjustment to 45 degrees
Mitre adjustment to ±45 degrees
Expandable worktop approximately 100 × 65cm
Table height approximately 82cm
Parallel guide and mitre gauge
Dust-collection ports
Guard, overload reset and IP54-rated switch listed
Assembly required

Possible fit: Buyers needing a published 85mm maximum cutting depth and a larger expandable table.

Limitations: The BTB50 product listing does not identify the laser guide supplied with the BTB60. Confirm blade arbor size, replacement-blade compatibility and dust-port measurements before purchasing accessories.

Check BTB50 details →

BAUMR-AG SBR-210 Sliding Compound Mitre Saw

The SBR-210 combines a 1500W motor with a 210mm, 24-tooth blade and sliding rails. Its primary role is controlled crosscutting, mitre cutting and left-bevel cutting.

Swivel range of ±45 degrees
Left bevel range of 0–45 degrees
Maximum listed 0°/90° capacity of 305 × 70mm
Maximum listed 0°/45° capacity of 215 × 70mm
Extendable work supports and securing clamp
Dust bag and vacuum connection
Class 2 laser guide
Approximately 11kg product weight

Specification discrepancy: The current specification table lists a no-load speed of 4500 RPM, while promotional text on the same page mentions 5800 RPM. Confirm the current model’s rating before purchase.

Possible fit: Crosscuts, trim, skirting, framing components and suitable mitred or bevelled timber.

Limitations: It does not replace a table saw for long rip cuts or a bandsaw for curves. A laser is an alignment aid and does not replace marking, measurement, clamping or correct blade positioning.

Check SBR-210 details →

BAUMR-AG BS40 Benchtop Bandsaw

The BS40 uses a 500W brushless motor and a 1712mm band blade. The current manufacturer information identifies wood and suitable plastic as its intended cutting materials.

Maximum cutting height of 115mm
Maximum cutting width of 245mm
Blade-width range listed as 3.5–12mm
Table approximately 302 × 304mm
Table tilt between 0 and 45 degrees
Micro-adjustable blade guard
Quick-lock fence clamp
Rapid blade-tension system
Dust-extraction port
Minimal assembly required

Possible fit: Curved cuts, suitable irregular shapes and straight cuts within the published throat and height capacity.

Limitations: It is not a metal or masonry saw. Blade width and tooth pattern affect the curve radius, material suitability and finish, so replacement blades must match the saw and intended work.

Check BS40 details →

Which Saw Type Fits the Job?

Cut or task	Likely saw type	Main consideration
Long straight rip cuts	Table saw	Fence alignment, support and kickback control
Repeated crosscuts	Mitre saw	Published width and height capacity
Mitre and bevel cuts	Compound mitre saw or table saw	Angle range, clamping and blade clearance
Curved cuts	Bandsaw	Blade width, tooth pattern and curve radius

Critical Workshop Saw Safety

Severe injury hazard: Contact with a moving blade or timber thrown by a saw can cause fatal or permanently disabling injuries. Guards, splitters, riving knives, clamps and push sticks must be used exactly as instructed.

Read the exact model manual before assembly, adjustment or operation.
Do not operate a saw unless its guards and safety devices are correctly fitted.
Secure the saw or stand on a firm, level and stable surface.
Wear suitable eye, hearing and respiratory protection.
Wear close-fitting clothing and secure long hair.
Keep hands away from the cutting line and use push sticks or suitable jigs where instructed.
Do not wear loose gloves near moving blades where they could become caught.
Support long or heavy material so it cannot fall, twist or lift during a cut.
Never reach over or behind a moving blade.
Keep bystanders away from the work area.
Disconnect power and wait for the blade to stop before adjustment, cleaning or maintenance.

Table-Saw Kickback

Kickback can throw timber towards the operator at high speed. Keep the blade guard and riving knife or splitter installed, use a correctly aligned fence, stand away from the likely kickback path and never make an unsupported freehand cut.

Mitre-Saw Operation

Clamp or support the workpiece as required by the manual. Keep hands outside the marked hazard area. Allow the blade to stop completely before raising the saw head or removing offcuts.

Bandsaw Operation

Adjust the exposed-blade guard close to the workpiece, use a push stick where required and avoid forcing tight curves that could twist or break the blade.

Electrical and Dust Safety

Use a compatible, RCD-protected power supply.
Keep plugs, outlets and connections dry.
Do not use damaged power cords, switches or plugs.
Use an extension lead only when permitted by the manual and correctly rated for the load and distance.
Connect suitable dust extraction where the saw provides a port.
Do not rely on a small collection bag to control all airborne dust.
Check the risks before cutting MDF, treated timber, painted material or plastic.
Never cut asbestos or suspected asbestos-containing material.

Checks Before Buying

Choose the saw type according to the cuts you actually need.
Check maximum cutting width and depth against your materials.
Measure the complete operating space, including infeed and outfeed clearance.
Confirm blade diameter, arbor, width and tooth specifications.
Check whether replacement blades are readily available.
Confirm dust-port measurements and extractor compatibility.
Check the power-supply and circuit requirements.
Allow for assembly, calibration and secure mounting.
Confirm current warranty terms and return-freight responsibilities.

Frequently Asked Questions

What is the difference between the BTB50 and BTB60?

The BTB60 has a 254mm blade and laser guide. The BTB50 has a 255mm blade and publishes cutting depths of 85mm at 90 degrees and 65mm at 45 degrees. Their tables, dimensions and supplied features also differ.

Which saw is suitable for curved cuts?

The BS40 bandsaw is the model in this comparison intended for suitable curved cuts. The achievable curve depends on the blade width, material and setup.

Which saw is intended for wide crosscuts?

The SBR-210 sliding mitre saw lists a maximum 0°/90° capacity of 305 × 70mm. Confirm the required angle and capacity before cutting.

Can these saws cut metal?

Do not assume they can. The products covered here are presented primarily as woodworking saws. Use only materials and blades expressly permitted by the exact model manual.

Does dust extraction remove the need for respiratory protection?

No. Dust extraction is an important control but may not capture every particle. Assess the material and use suitable respiratory protection where required.

Has Firebusters tested these saws?

No. This comparison is based on published manufacturer, merchant and official safety information.

Final Assessment

The BTB50 and BTB60 are separate table-saw models for supported straight and angled cuts. The SBR-210 is designed around sliding crosscuts, mitres and left-bevel work. The BS40 provides a different capability for curves and suitable irregular shapes.

Compare the required cut, material, blade specification, available space, dust control and your ability to operate the machine safely. Confirm the latest specifications, warranty and package contents before ordering.

Sources

Sources checked 4 September 2026. Specifications, availability, package contents and warranty conditions can change.